server rack,Jaunty-Fabricator Enterprise Industrial Co., Ltd.
Google 網站翻譯


包含商品編號 包含商品描述
簡易溫控 ThermoStat-710442 ThermoStat-710442_簡易型溫控 ThermoStat for Racks and Cabinets with Mounting clip,簡易型溫控使用固定夾片安裝於機櫃產品,達成溫度控制及散熱之目的.   ThermoStat-710442_簡易溫控 簡易型溫控使用固定夾片安裝於機櫃產品,達成溫度控制及散熱之目的.     ※首先決定簡易型溫控之安裝位置,所需最小空間為 (60 x 33 x 43 mm公厘) . ThermoStat-710442_BottomView ※風扇組(改裝轉接)連結線,連結至圖(A)之接點(無極性區分),並鎖緊簡易式溫控之結線端子螺絲,如圖(B)所示. ThermoStat-710442_FrontView ※拆下風扇組原結線,如圖示之母插銷(F1),連結改裝轉接之連結線(公對公插銷延長線),如圖(C) 所示,連結至簡易式溫度控制器. ThermoStat-710442_Wiring ※設定簡易式溫度控制器之所需溫度,如圖(D)所示,環境溫度超過設定溫度時風扇將啟動. 溫度設定範圍為 0 - 60˚C. ※使用標準型35 mm DIN 滑軌固定簡易式溫度控制器,如圖(E)所示 . ThermoStat-710442_RearView
0 顆星評價!
  Operation Instruction of Temperature Control Unit Operation Instruction of Temperature Control Unit Temperature control unit is used for controlling temperature of inner cabinet mainly with features of high reliability, easy operation. Meanwhile, it has other warning functions such as alarm for reaching max temperature limit, outputting, sensor fault alarm, etc. I. The specification and technical parameter * Running environment: -5oC~50oC * Relative humidity:20%~85%(dew don’t be formed) * Main technical parameter The voltage of the power: 220 VAC±10% (110VAC is optional) * Measuring Scale: 0oC~50oC * Capacity of connective point of relay: 7A/250 VAC * Span of control: 0oC~50oC *Precision of controlling and measuring: ±1oC II. Surface dimension and explanation of each part 1. temperature controller 2. switch 3. power input 4. sensor tie-in (connect) 5. power output (1) 6. power output (2) III. Connection /wiring Steps 1. Connect the temperature sensor to the sensor of temperature controlling unit. 2. Connect the outside power to the power plug of temperature controlling unit with special cable IV. Operation When complete all the connection steps above and confirm the connection is ok, then turn on the switch on the temperature controller and adjust the control parameter to appropriate temperature. V. Operation of the temperature controller 1. Look over and set parameter (1)Look over parameter. Under the state of non-setting, pressing key ▲ show setting value of temperature. Pressing key ▼ display the different between the present temperature and temperature located, 2 seconds later, the screen will show the present temperature. (2)Set parameter * method of entering into the state of customer setting: under not-setting state. Press “SET” key longer than 5 seconds to enter customer state of setting up, setting indicator to be on and to show the temperature at present. * method of temperature setting :under the state of customer setting , press ▲ upwards or ▼downwards to adjust the temperature .Press one time to adjust 1 degree. It will be changed into rapid adjusting after pressing on it over 2 seconds. *The method of exit from the state of customer setting Press SET key 5 seconds or no any operation within 30 second under state of customer setting, system will store current setting, value and return to normal working condition. *Method of entering administrator’s menu: under state of non-setting, pressing “SET” and ▲over 5 seconds at the same time to enter administrator’s menu Then setting light will be on to show the item: F1 to setting. *The method of altering setting items and entering into state of parameter setting: Under setting state, press ▲ upward or ▼ downward to adjust item from F0 to F1.
0 顆星評價!
WebDiY 網路開店 GO! 系統